top of page

SDI 2220 & 2276
HIGH-PERFORMANCE ACCELEROMETERS

Contact Us for a Quote
SDI Accelerometers at DigiKey
SDI model 2220 and 2276 accelerometers
Download the SDI 2220 & 2276 Datasheet

SDI’s Premium Models 2220 and 2276 High-Performance Single Axis MEMS DC Accelerometers are rugged plug-and-play measurement devices that provide enhanced performance over temperature for use in zero to medium frequency applications experiencing large or rapid temperature variations or maintaining hot or cold extremes for extended periods of time

AVAILABLE

G-RANGES

± 2 g

± 5 g

± 10 g

± 25 g

± 50 g

± 100 g

± 200 g

± 400 g

  • Low Noise: 10 μg/rootHz Typical for ±2g Full Scale Versions

  • -55 to +125°C Operating Temperature Range 

  • Flexible +8 to +32 VDC Power  

  • Excellent Long-Term Stability

  • ±4V Differential Output or 0.5V to 4.5V Single Ended Output

  • Responds to frequencies from zero (DC) to 2000+ Hz

  • Low Impedance Outputs Support up to 2000 Feet of Cable

  • Integrated Cable or Connector, Traditional 1” & Small Footprint Sizes

  • Simple Four (4) Wire Connection

  • Rugged Anodized Aluminum Case

  • Fully Calibrated and Serialized for Traceability

Quick Links

1-Axis

3-Axis

The 2220 comes in a traditional 1-inch square package with a 10' integrated cable and is operationally identical to the 2276, the small footprint device designed for tight spaces.  The 2220 and 2276 feature a hermetically sealed, low noise SDI Model 1522 surface mount accelerometer, which is individually tested, programmed, calibrated and verified in a climate chamber to ensure the greatest accuracy in thermally volatile conditions.  The 2220 and 2276 include initial calibration reports.

Onboard voltage regulation and an internal voltage reference eliminate the need for precision power supplies. The robust, anodized aluminum case is potted then epoxy sealed and can be mounted easily via two screws, an adhesive, or by attaching a magnet.  

ZERO TO MEDIUM FREQUENCY APPLICATIONS

SDI Accelerometer apps
g Range
Sensitivity, Differential
Frequency Response (Typ, 3 dB)
Frequency Response (Min, 3 dB)
Frequency Response (Typ, 5%)
Output Noise, Differential (RMS, Typ)
Max. Mechanical Shock (0.1 ms)
g
mV/g
Hz
Hz
Hz
μg/(root Hz)
g (peak)
±2
2000
0 – 525
0 – 300
0 – 250
10
2000
±5
800
0 – 800
0 – 420
0 – 400
15
2000
±10
400
0 – 1100
0 – 660
0 – 700
23
5000
±25
160
0 – 1750
0 – 1050
0 – 1300
38
5000
±50
80
0 – 2100
0 – 1400
0 – 1600
60
5000
±100
40
0 – 3000
0 – 1700
0 – 1700
121
5000
±200
20
0 – 3600
0 – 2100
0 – 1900
243
5000
±400
10
0 – 4200
0 – 2400
0 – 2000
475
5000

OPERATION

SDI Models 2220 and 2276 MEMS DC Accelerometers provide optimal performance when they are connected to instrumentation in a differential configuration using both the AOP and AON output signals, but they also support single ended operation for complete flexibility. 

 

These Accelerometers produce differential analog output voltage pairs (AON & AOP) which vary with acceleration.  The signal outputs are fully differential about a common mode voltage of approximately 2.5 volts.  At zero acceleration, the output differential voltage is nominally 0 volts DC; at ±full scale acceleration, the output is ±4 volts DC, respectively, as shown in the figure (below).  The output scale factor is independent from the supply voltage of +8 to +32 volts. 

 

When a differential connection is not possible, SDI recommends connecting the accelerometer to instrumentation in single ended mode by connecting AOP and GND to the instrumentation and leaving AON disconnected.  Keep in mind that the signal to noise ratio is reduced by half for a single-ended vs. a differential connection.

Differential and single ended output plots

PERFORMANCE - ALL VERSIONS

All Models: Unless otherwise specified, Vs=+8 to +32 VDC, TC=25°C, Differential Mode.  Span = ±g range = 8000 mV.

Note (1): For 2g thru 50g only; 100g and greater versions are tested and specified from -65 to +65g.

NOTICE:  Stresses greater than those listed may cause permanent damage to the device.  These are maximum stress ratings only.  Functional operation of the device at or above these conditions is not implied.

PACKAGE DIMENSIONS

SDI 2220 and 2276 packages

Please see the data sheet for sensor location and other additional details. 

request your quote
Download the SDI 2220 & 2276 Datasheet

OPTIONAL ACCESSORIES

Model 2230 Triaxial Mounting Block

  • Anodized 6061-T6 aluminum 1.25" cube

  • Mix and Match g-levels for custom combinations

SDI 2235 block

Model 2232 Magnetic Mount

  • 10 lbs / 4.6 KG pull force

  • Rated for use up to +/-50G

  • Low mass: 23 grams

SDI 2232 magnet block

Model 2235 Stud Mount Adaptor Block

  • Stud mount Adaptor for any SDI module

  • Anodized 6061-T6 aluminum block

  • 6.2 grams, 0.7” x 1” footprint

SDI 2235 block

3-AXIS VERSIONS

SDI’s high-performance, single axis accelerometers are also built in three-axis configurations for multi-dimensional sensing in one package with only a single excitation connection.  The high-performance SDI Models 2470 and 2476 are the three axis versions of the 2220 and 2276 with similarly upgraded SDI Model 1522 surface mount accelerometers, improved bias and scale factor temperature shift performance, and include an initial calibration certificate.  The 2470 includes a 3-foot integrated cable and is operationally identical to the 2476, which features a connector for easily customized cable lengths and positions.    

SDI Model 2470 accelerometer
SDI model 2476 accelerometer
bottom of page